Do You Need Council Approval for a Granny Flat in Queensland?
Superior Granny Flats Team
Thinking about adding a granny flat to your Queensland property? Before you get too far into floor plans and finishes, there's a more fundamental question to answer: do you actually need prior council approval?
The short answer is that building approval is required for almost every secondary dwelling in Queensland, but whether you also need a full development application from your local council depends on your site, its zoning, and the size of what you're planning to build. Get this part wrong, and you could be looking at costly delays, forced changes to your design, or worse, an order to remove a structure that was never properly approved.
This guide walks through what Queensland councils actually require, when a granny flat qualifies as "accepted development" that skips the formal approval process, and what can tip a project into needing a full DA.
If you're planning a granny flat on the Gold Coast, in Brisbane, or elsewhere in Queensland, understanding these rules upfront will save you time, money, and a fair amount of frustration.
What Is a Granny Flat (Secondary Dwelling) in Queensland?
In Queensland, a Granny Flat is officially defined as a secondary dwelling. It is a self-contained living space that is on the same property as the primary residence. It remains on the same title as the main house and cannot be subdivided, sold or strata-titled separately.
This secondary dwelling must be self-contained, with its own kitchen area, bathroom and laundry facilities, as well as bedroom(s) and a living area. All of this must be contained in a residence that is smaller in scale and function than the main dwelling.
Do You Always Need Council Approval?
There is a two-tiered system in Queensland for building approvals. There is building approval and there is development approval, which only applies if it falls outside ‘accepted development’.
What does not need approval
Minor projects that meet a specific size, height and location limits are classified as ‘accepted development’. You can complete these projects without formal approval from the council. Examples of work that does not require approval include:
- Cosmetic internal updates: Painting, new flooring, and replacing kitchen cupboards.
- Small outdoor structures: A small tool shed up to 10 square metres.
- Low fences: Fences no higher than 2 metres (depending on corner visibility).
- Low retaining walls: Walls under 1 metre high that do not support a structure.
- Minor renovations: Standard, internal alterations or low-impact repairs to an existing home.

Work That Needs Approval
Major changes, structural adjustments, or work on restricted properties require formal assessment. You need approval if your project involves:
- Structural changes: Altering load-bearing walls or roof framing.
- Additions: Increasing the overall floor area of a home, including adding attached carports, garages, or large decks.
- Special overlays: Properties with heritage listings, or those in specific council overlay and neighbourhood plan zones.
- Plumbing and safety: Moving plumbing layouts, changing fire safety compliance, or altering the building classification.
Council vs. Private Certifiers
In Queensland, building approvals are usually handled by a licensed private building certifier. However, you may still need a development application (planning approval) from the local council if your design breaches standard setbacks, heights, or local planning codes. You can verify your property rules using tools like Queensland Globe or your local council's online planning map.
What Counts as "Accepted Development"?

Accepted Development is a category of development under the Planning Act 2016 (Qld). This does not require formal town planning approval or permit from the local council or state government. These projects are generally low-risk and compatible with the local area, hence they are exempt from the lengthy development assessment process.
There are two sub-categories of Accepted Development.
Accepted development without requirements
You can immediately proceed with your project. No formal checklists or government rules need to be actively assessed, though basic site rules (like not trespassing) still apply.
Accepted development with requirements
The project is only "accepted" if it meets strict, pre-defined design rules, thresholds, and performance criteria (such as height restrictions or boundary setbacks).
What Can Trigger a Full Development Application
When a project fails to meet the ‘accepted development’ criteria, or when a significant change to the use of land is proposed, then you need to make a full Development Application (DA) to the local council. If any of the following triggers apply , then you will need council approval for your secondary dwelling.
- Material Change of Use (MCU). This is where you choose to change how the land is being used, such as turning a house into a childcare centre or a cafe, or starting a new use of the land, such as a knock-down-rebuild.
- Reconfiguration of a Lot (ROL). If you’re adjusting a property boundary or you’re subdividing your land, then a DA is required.
- Heritage Overlays. Building or renovating a property that is located in a Character Residential Zone can trigger a DA. So too can altering a pre-1947 building or working on a site that has a heritage listing.
- Non-compliant Design. If you plan to exceed local building heights, adjust the setback from the road or if there are parking minimums specified, then a DA will be required.
- Major House Renovations and Extensions. If you’re creating new habitable space in an existing house, or adding another storey to a current residence, then a DA will be required.
- State Interest Triggers. If your project impacts a state-controlled transport corridor, environmental protections or a coastal area that requires referral to the State Assessment and Referral Agency.
Size and Site Rules to Know
Navigating size and site rules in Queensland is essential for any construction or extension project, including a secondary dwelling or a simple backyard shed. Development in Queensland is unique because it is managed through a multi-layered system: statewide standards dictate basic setbacks and structural definitions via the Queensland Development Code (QDC), while local councils specify the exact size and site limits through their independent planning schemes.
The core size, site, and boundary rules to know across Queensland include:
A standard lot size is 450m² or larger. You need to keep all structures at least 1.5 metres from the boundary and at least 6 metres back from the street line.
Small lots, under 450m², have tighter rules. You can get to within 1 metre of side and rear boundaries, or less, depending on each local council’s specific small-lot code.
If your design cannot meet these distances (e.g., wanting to place a carport right on the fence line), you must apply for a Siting Relaxation / Siting Variation through your local council before starting construction.
For most suburban residential lots, the maximum allowed site cover is typically 50% to 60% of the total land area. This refers to the portion of your block covered by roofed buildings, including your secondary dwelling.
As well as site cover, major councils like Brisbane City Council require a specific percentage of landscaped open space (usually 20–35% of the block) to manage stormwater drainage and urban greening.
You can build a small garden shed or non-habitable outbuilding as "accepted development" without full building or planning approval, provided your shed is no larger than 10 square metres, is no taller than 2.4 metres and no side is longer than 5 metres.
Since state planning reforms dropped the rule restricting granny flat tenancies to family members, secondary dwellings have surged in popularity. There is no single statewide maximum size for a granny flat; the limit is set entirely by your local council's planning scheme. If you're planning a granny flat, Gold Coast council rules are among the most detailed in the state, particularly around site cover and parking:
| Local Council Area | Max Gross Floor Area (GFA) | Key Proximity / Site Rule |
| Brisbane City Council | 80m² | Must be located within 20 metres of the main house. |
| Gold Coast City Council | 80m² (up to 90m² on rural lots) | Max 50% overall site cover; requires 1 extra on-site parking spot. |
| Logan City Council | 70m² (up to 100m² on lots ≥ 1,000m²) | Must be built behind or within 20m of the main house. |
| Moreton Bay City Council | 45m² (up to 55m² on lots ≥ 800m²) | Tighter proximity limit; must be within 10 metres of the primary house. |
Note: All new granny flats must meet National Construction Code (NCC) energy efficiency requirements and have structural approval, even if they bypass local planning applications.
Renting Out Your Granny Flat
As mentioned above, in September 2022, a rule change allowed owners of a secondary dwelling in Queensland to rent them out to anyone, related or not. You can now offer your granny flat as a standard rental accommodation to anyone who applies.
Why It Pays to Get This Right the First Time
Council approval rules for granny flats in Queensland aren't a single, statewide checklist, they're a patchwork of state legislation, local planning schemes, and council-specific size limits that can catch even experienced homeowners off guard. Get the assessment wrong, and you could face costly redesigns, delays, or an approval process that drags on far longer than it needs to.
That's where working with a builder who understands the Queensland system from the outset makes the difference. From confirming whether your project qualifies as accepted development to navigating a full DA if your site requires one, getting expert advice early means fewer surprises and a smoother path from concept to completion.
If you're after some of the best granny flats Queensland has to offer, on the Gold Coast, in Brisbane, or anywhere else in Queensland, Superior Granny Flats can help you understand exactly what your project needs before you commit to a design.
- How Big Can a Granny Flat Be? Size Limits at 60m², 70m² and 80m²
- What It Takes to Get a Granny Flat Approved in Victoria and Queensland
- How to Split Utility Bills Between the Main House and a Granny Flat
- Airbnb vs. Long-Term Leases: Maximising Income from Your Backyard Studio
- How to Optimise Small Studio Granny Flat Floor Plans for Maximum Comfort
Brands We Work With
for further information